HOW TO PLAN A SITE INVESTIGATION PROGRAM?


HOW TO PLAN A SITE INVESTIGATION PROGRAM?


SITE EXPLORATION PROGRAM

The knowledge about the site forms a vital role in the safe and economical development of a site. A thorough investigation of the site is an essential preliminary to the construction of any civil engineering works. Public building officials may require soil data together with the recommendations of the geotechnical consultant prior to issuance of a building permit. Elimination of the site exploration, which usually ranges from about 0.5 to1 percent of total construction costs, only to find after construction has started that the foundation must be redesigned is certainly false economy. This is generally recognized, and it is doubtful if any major structures are currently designed without exploration being undertaken.

OBJECTIVES OF SITE INVESTIGATION

The primary objectives of soil exploration is mentioned below
  • To access the general suitability of the site
  • To achieve safe and economical design of foundations and temporary works
  • To know the nature of each stratum and engineering properties of the soil and rock, that may affect the design and mode of construction of proposed structure and foundation
  • To foresee and provide against difficulties that may arise during construction due to ground and other local conditions
  • To find out the sources of construction material and selection of sites for disposal of water or surplus material
  • To investigate the occurrence or causes of all natural and manmade changes in conditions and the results arising from such changes
  • To ensure the safety of surrounding existing structures
  • To design for the failed structures or remedial measures for the structures deemed to be unsafe
  • To locate the ground water level and possible corrosive effect of soil and water on foundation material

PLANNING FOR SITE EXPLORATION

The planning of the site exploration program involves location and depth of borings, test pits or other methods to be used, and methods of sampling and tests to be carried out. The purpose of the exploration program is to determine, within practical limits, the stratification and engineering properties of the soils underlying the site. The principal properties of interest will be the strength, deformation, and hydraulic characteristics. The program should be planned so that the maximum amount of information can be obtained at minimum cost. In the earlier stages of an investigation, the information available is often inadequate to allow a firm and detailed plan to be made.
The investigation is therefore performed in the following phases:
  1. Fact finding and geological survey
  2. Reconnaissance
  3. Preliminary exploration
  4. Detailed exploration

1. FACT FINDING AND GEOLOGICAL SURVEY

Assemble all information on dimensions, column spacing, type and use of structure, basement requirements, and any special architectural considerations of the proposed building. Foundation regulations in the local building code should be consulted for any special requirements. For bridges the soil engineer should have access to type and span lengths as well as pier loadings. This information will indicate any settlement limitations, and can be used to estimate foundation loads.

2. RECONNAISSANCE

This may be in the form of a field trip to the site which can reveal information on the type and behavior of adjacent sites and structures such as cracks, noticeable sags, and possibly sticking doors and windows. The type of local existing structure may influence, to a considerable extent, the exploration program and the best foundation type for the proposed adjacent structure. Since nearby existing structures must be maintained, excavations or vibrations will have to be carefully controlled. Erosion in existing cuts (or ditches) may also be observed. For highways, run off patterns, as well as soil stratification to the depth of the erosion cut, may be observed. Rocky outcrops may give an indication of the presence or the depth of bedrock.

3. PRELIMINARY EXPLORATION

In this phase a few borings are made or a test pit is opened to establish in a general manner the stratification, types of soil to be expected, and possibly the location of the groundwater table. One or more borings should be taken to rock, or competent strata, if the initial borings indicate the upper soil is loose or highly compressible. This amount of soil exploration is usually the extent of the site investigation for small structures. A feasibility exploration program should include enough site data and sample recovery to approximately establish the foundation design and identify the construction procedures. It is common at this stage to limit the number of good quality samples recovered and rely heavily on strength and settlement correlations using index properties such as liquid limit, plasticity index, and penetration data together with unconfined compression tests on samples recovered during penetration testing.

4. DETAILED EXPLORATION

Where the preliminary site investigation has established the feasibility of the project, a more detailed exploration program is undertaken. The preliminary borings and data are used as a basis for locating additional borings, which should be confirmatory in nature, and determining the additional samples required. If the soil is relatively uniform in stratification, a rather orderly spacing of borings at locations close to critical superstructure elements should be made. On occasion additional borings will be required to delineate zones of poor soil, rock outcrops, fills, and other areas which can influence the design and construction of the foundation. Sufficient additional samples should be recovered to redefine the design and for any construction procedure required by the contractor to install the foundation. This should avoid an excessive bid for the foundation work, cost overruns, and damage to adjacent property owners from unanticipated soil conditions discovered when the excavation is opened.

Comments

Post a Comment

Popular posts from this blog

40+ Construction Tools List with Images for Building Construction

Image
Construction tools list for building construction works such as concrete, brick masonry, leveling, wood works, floor works, slab works, brick laying, plastering etc. is provided. Every construction tool is necessary to achieve good results in the whole project. Along with these tools, the workers should also use some safety tools to prevent them from the unexpected accidents. Construction Tools List for Building Construction Some important construction tools and their uses are listed below: Bolster Boning rod Brick hammer Bump cutter/screed Chisel Circular saw Concrete mixer Cordless drill Crowbar Digging bar End frames Float Gloves Hand saw Helmet Hoe Iron pan Jack plane Ladder Line and pins Mason’s square Measuring box Measuring tape Measuring wheel Pick axe Plumb bob Plumb rule Polishers Putty knife Rammer Rubber Boots Safety glasses Safety helmet Sand screen machine Scratchers Sledge hammer Spade Spirit level Straight edge brushes Til...
Read more

Building Materials properties and their Importance in Construction

Image
Building materials or construction materials are the major requirement in this modern age of technology. There are many types of building materials used for different construction works. Properties of Building Materials For a material to be considered as building material, it should have required engineering properties suitable for construction works. These properties of building materials are responsible for its quality and capacity and helps to decide applications of these material. Such properties of building materials are categorized as follows. Physical properties Mechanical properties Chemical properties Electrical properties Magnetic properties Thermal properties Physical Properties of Building Materials These are the properties required to estimate the quality and condition of the material without any external force. The physical properties of engineering materials are as follows. Bulk density Porosity Durability Density Density index Specific gravity ...
Read more

How to Prevent Errors During Setting Out Building Plan on Ground?

Image
Setting out building plan on ground is one of the most significant steps in building constructions and any errors at this stage would cause considerable problems, if it is not tackled immediately. Errors During Setting Out Building Plan on Ground There are different types of errors that might be made when a structure is set out for example gross errors, systematic errors and random errors. These errors should be prevented and there are some measures to tackle these issues. These measures will be discussed in the following sections. Fig.1: Setting Out of Building Plan on Ground Fig.2: Setting Out Building Plan on Ground How to Prevent Errors During Setting Out of Building? Following are the different types of control that should be carried out to prevent any errors during setting out building plan on ground: Good practice in office On site control Equipment and staff Checks Marking the ground Use of grid offset Good Practice in Office To successfully set...
Read more

Factors Affecting Selection of Foundation for Buildings?

Image
Factors which affect selection of foundation for a building can be many from the soil conditions to the type of structure and loads from the building. All the factors are considered during selection of foundation for durable building construction. Factors Affecting Selection of Foundation Following are the factors which affect the selection of suitable foundations for building construction: Loads from building Type of soil Type of structures in neighborhood Type of foundations 1. Loads from Building The first factor considered is loads from building on the foundation. This load is a combination of dead load and imposed loads on the buildings. Other loads such as wind loads, earthquake loads, snow loads etc. are also considered based on location. The quantity of loads depends on the type of structure, number of floors and material of construction. As the number of floors increases, the dead load and imposed loads also increase. Choice of material for construction su...
Read more

Ceiling types used in Building Construction and their Applications

Image
Various types of ceiling are used in building construction. Applications, aesthetics, advantages and disadvantages of these types of ceilings are discussed in this article. The ceiling of a building form one of the most important structural elements it terms of functionality as well as creativity which in turn bring good aesthetics to the building interior. This document would help you understand ceilings that in turn would help you understand the most suitable options while undertaking either repair or renovation work of our building interior. The ceiling gains a definition, ” A part of a building which encloses and is exposed overhead in a room, protected shaft or circulation space.” It helps us to create an enclosure and separation between spaces. They provide perfect lighting in the room by controlling diffusion of light. It also controls the sound around a room by making the room sound proof. It, therefore, stops the passage of sound between the rooms. Now ceiling also po...
Read more

HOW TO DETERMINE DEPTH OF FOUNDATION

Image
Many factors affects the determination of depth of foundation. Calculation for foundation depth is done based on type of soil, ground water table, loads from structure, bearing capacity of soil and other factors. General factors to be considered for determining depth of foundation are: 1. Load applied from structure to the foundation 2. Bearing capacity of soil 3. Depth of water level below the ground surface 4. Types of soil and depth of layers in case of layered soil 5. Depth of adjacent foundation The minimum depth of foundation should be considered to ensure that the soil is having the required safe bearing capacity as assumed in the design. However, it is advised to carry out soil investigation before deciding on depth of foundation. Soil investigation report will suggest the foundation depth based on the type of structure, soil properties, depth of water table, and all other variable that should be considered. Soil investigation report provides bearing capacity of ...
Read more

WHAT IS VOLUME BATCHING OF CONCRETE AND HOW IT IS DONE IN FIELD?

Image
WHAT IS VOLUME BATCHING OF CONCRETE? Batching of concrete means measuring different ingredients of concrete (i.e. cement, sand, coarse aggregate and water) before mixing it. When this measurement is done on the basis of volume, we call it  Volume Batching . Below are mentioned some of important points to remember before adopting volume batching method in field. Volume batching is not a good method for measuring concrete materials. It is not applicable in case of reinforced concrete structure. This method of concrete batching may not be economical. It can be only used for unimportant concrete or for small concrete works. HOW VOLUME BATCHING IS DONE IN FIELD? Before batching concrete ingredients in terms of volume, we need to know two things. What is the relative proportion of concrete ingredients in terms of volume? What is the water-cement ratio? After knowing these two things you can proceed to batch concrete ingredients in field. The table shown below ca...
Read more

Construction Project Management Softwares

Image
Construction PM Software A new wave of web and cloud apps are streamlining communication, simplifying document management, and improving efficiency in construction management.  Here are some of top construction management tools: Smartsheet Smartsheet  is a spreadsheet-inspired work management tool with robust collaboration and communication features. With pre-built construction templates, it’s easy to create a timeline, track progress, manage documents, and organize the details. Gantt charts are automatically created and auto-adjust every time a change is made, so you can share the most up-to-date timeline with team members or stakeholders. You can upload files from your computer, Google Drive, Box, Dropbox, Evernote, or add a web URL, creating a central repository for all project documentation and contracts. Team members can have discussions directly in the sheet and set reminders and alerts, so everyone is on the same page. And lastly, Smartsheet inte...
Read more

Methods of underpinning, Procedure and Applications in Foundation Strengthening

Image
Underpinning is a method for repair and strengthening of building foundations. Underpinning methods, procedures and their applications in strengthening of different types of foundations is discussed in this article. There are situations where a failure in foundation or footing happens unexpectedly after the completion of whole structure (both sub and superstructure). Under such emergency situation, a remedial method has to be suggested to regain the structural stability. The  method of underpinning  help to strengthen the foundation of an existing building or any other infrastructure. These involve installation of permanent or temporary support to an already held foundation so that additional depth and bearing capacity is achieved. Selection of Underpinning Methods Underpinning methods are selected based on age of structure and types of works involved. Structure categories based on its age: Ancient Structures :Age greater than 150 years Recent Structures : Age ...
Read more

Methods for Calculating Cost of Engineering Consultant Services

Image
here are several methods by which calculation of engineering consultant services cost can be carried out in construction. It is possible to employ various charging approach at different phase of the consultant services. The application of each method or combination of methods is dependent on nature, scope and complexity of the required engineering services. In this article, these charging consulting services are discussed. Following are the topics discussed for calculating cost of engineering services or consulting services in construction: What are the factors that affect the engineering service cost? Methods for charging engineering services What are the Factors that affect the Engineering Service Cost in Construction? There are various factors that control the cost of engineering services required for a specific project. These factors are outlined below: The conditions at project site. Degree of danger that may be encountered and exposure possibility. System of pr...
Read more