HOW TO MAKE TEST CUBES FROM FRESH CONCRETE?


MAKING OF TEST CUBES FROM FRESH CONCRETE

IS-456 has laid down the acceptance criteria of quality concrete. In all the cases, the 28-days compressive strength shall alone be the criterion for acceptance or rejection of the concrete. 7 days compressive strength of concrete can be carried out in order to get a relatively quicker idea regarding the quality of concrete.

PROCEDURE OF TEST CUBE PREPARATION

EQUIPMENT

The following equipments are needed for the preparation of concrete cubes.
  1. Sample tray;
  2. Mould for making test cube;
  3. Spanner;
  4. Scoop;
  5. Steel float or trowel;
  6. Compacting bar;
  7. Cleaning rags;
  8. A bucket or barrow for transporting the samples;
  9. Curing tank
  10. Permanent Marker.
lb001

NO OF CUBES

6 no of Cubes of 150 x 150 x 150 mm size shall be cast, 3 for 7-days testing and 3 for 28-days testing. A sample consists of 3 cube specimens and their average compressive strength represents the test result of that sample. The individual variation of a set of 3 cubes should not be more than ± 15% of the average. If more, the test result of the sample is invalid.

SAMPLE OF CONCRETE

Sample of concrete for test specimen shall be taken at the mixer or in the case of ready mixed concrete from the transportation vehicle at the time of discharge. Such samples shall be obtained by repeatedly passing a scoop or pail through the discharge stream of the concrete. The samples thus obtained shall be mixed on a non-absorbent base with shovel until it is uniform in appearance.
lb005
Number of samples to be taken depends on the quantity of concrete. As per IS-456, the following table shall be followed during sampling.
Quantity of concrete in the work (m3)Number of samples
1-51
6-152
16-303
31-504
51 and above4 plus one additional sample for each additional 50 m3 or part thereof.
Note:- Frequency of sampling may be agreed upon internally by supplier and purchaser.

CASTING OF CUBES

The cube mould plates should be removed, properly cleaned assembled and all the bolts should be fully tight. A thin layer of oil then shall be applied on all the faces of the mould. It is important that cube side faces must be parallel.
lb002
lb003
After taking concrete samples and mixing them, the cubes shall be cast as soon as possible as described below.

CASTING & COMPACTION BY HAND

The concrete sample shall be filled into the cube moulds in 3 layers, each layer approximately 5 cm deep. In placing each scoopful of concrete, the scoop shall be moved around the top edge of the mould as the concrete slides from it, in order to ensure a symmetrical distribution of the concrete within the mould. Each layer shall be compacted either by hand or by the vibration. Each layer of the concrete filled in the mould shall be compacted by not less than 35 strokes by tamping bar. The strokes shall be penetrating into the underlying layer and the bottom layer shall be rodded throughout its depth. Where voids are left by the tamping bar the sides of the mould shall be tapped to close the voids.
lb007
lb008

CURING

The casted cubes shall be stored under shed at a place free from the vibration at a temperature 220C to 330C for 24 hours covered with wet straw or gunny sacking.

MARKING

Immediately after initial curing of the cubes they should be marked clearly. This can be done by writing the details of the cube in ink on a small piece of paper and placing on top of the concrete until it is demoulded.
lb011
The cube shall be removed from the moulds at the end of 24 hours and immersed in clean water at a temperature 240C to 300C till the 7 or 28-days age of testing. The cubes shall be tested in the saturated and surface dry condition.
For the true representation of actual strength of concrete in the structure, extra cubes shall be cast, stored and curded as per the identical conditions of that structure, and tested at required age.

NOTE: WHEN MOULDS ARE NOT IN USE, APPLY A THIN LAYER OF OIL OVER THE INSIDE SURFACE OF THE MOULD AND KEEP IT IN A SAFE PLACE.

Comments

Anonymous said…
Hello, Everyone,I'm Adrik Vadim living in Kurgan City , I want to share with you all on here on how Mr Benjamin help me with a loan of 15,000.000.00 Rubles to start up my food beverage delivery after all I have work in several hotels here in kurgan just to earn a living but unfortunate I was still having difficulties to pay a rent but I thank God now that I'm a self employ now with 5 workers working in my care. Just if you looking for financial freedom I will advise you contact Mr Benjamin with this email below and whats app number as well. lfdsloans@outlook.com +1-989-394-3740
27 June 2020 at 09:00
Post a Comment

Popular posts from this blog

40+ Construction Tools List with Images for Building Construction

Image
Construction tools list for building construction works such as concrete, brick masonry, leveling, wood works, floor works, slab works, brick laying, plastering etc. is provided. Every construction tool is necessary to achieve good results in the whole project. Along with these tools, the workers should also use some safety tools to prevent them from the unexpected accidents. Construction Tools List for Building Construction Some important construction tools and their uses are listed below: Bolster Boning rod Brick hammer Bump cutter/screed Chisel Circular saw Concrete mixer Cordless drill Crowbar Digging bar End frames Float Gloves Hand saw Helmet Hoe Iron pan Jack plane Ladder Line and pins Mason’s square Measuring box Measuring tape Measuring wheel Pick axe Plumb bob Plumb rule Polishers Putty knife Rammer Rubber Boots Safety glasses Safety helmet Sand screen machine Scratchers Sledge hammer Spade Spirit level Straight edge brushes Til
Read more

Building Materials properties and their Importance in Construction

Image
Building materials or construction materials are the major requirement in this modern age of technology. There are many types of building materials used for different construction works. Properties of Building Materials For a material to be considered as building material, it should have required engineering properties suitable for construction works. These properties of building materials are responsible for its quality and capacity and helps to decide applications of these material. Such properties of building materials are categorized as follows. Physical properties Mechanical properties Chemical properties Electrical properties Magnetic properties Thermal properties Physical Properties of Building Materials These are the properties required to estimate the quality and condition of the material without any external force. The physical properties of engineering materials are as follows. Bulk density Porosity Durability Density Density index Specific gravity
Read more

How to Prevent Errors During Setting Out Building Plan on Ground?

Image
Setting out building plan on ground is one of the most significant steps in building constructions and any errors at this stage would cause considerable problems, if it is not tackled immediately. Errors During Setting Out Building Plan on Ground There are different types of errors that might be made when a structure is set out for example gross errors, systematic errors and random errors. These errors should be prevented and there are some measures to tackle these issues. These measures will be discussed in the following sections. Fig.1: Setting Out of Building Plan on Ground Fig.2: Setting Out Building Plan on Ground How to Prevent Errors During Setting Out of Building? Following are the different types of control that should be carried out to prevent any errors during setting out building plan on ground: Good practice in office On site control Equipment and staff Checks Marking the ground Use of grid offset Good Practice in Office To successfully set
Read more

Factors Affecting Selection of Foundation for Buildings?

Image
Factors which affect selection of foundation for a building can be many from the soil conditions to the type of structure and loads from the building. All the factors are considered during selection of foundation for durable building construction. Factors Affecting Selection of Foundation Following are the factors which affect the selection of suitable foundations for building construction: Loads from building Type of soil Type of structures in neighborhood Type of foundations 1. Loads from Building The first factor considered is loads from building on the foundation. This load is a combination of dead load and imposed loads on the buildings. Other loads such as wind loads, earthquake loads, snow loads etc. are also considered based on location. The quantity of loads depends on the type of structure, number of floors and material of construction. As the number of floors increases, the dead load and imposed loads also increase. Choice of material for construction su
Read more

Ceiling types used in Building Construction and their Applications

Image
Various types of ceiling are used in building construction. Applications, aesthetics, advantages and disadvantages of these types of ceilings are discussed in this article. The ceiling of a building form one of the most important structural elements it terms of functionality as well as creativity which in turn bring good aesthetics to the building interior. This document would help you understand ceilings that in turn would help you understand the most suitable options while undertaking either repair or renovation work of our building interior. The ceiling gains a definition, ” A part of a building which encloses and is exposed overhead in a room, protected shaft or circulation space.” It helps us to create an enclosure and separation between spaces. They provide perfect lighting in the room by controlling diffusion of light. It also controls the sound around a room by making the room sound proof. It, therefore, stops the passage of sound between the rooms. Now ceiling also po
Read more

HOW TO DETERMINE DEPTH OF FOUNDATION

Image
Many factors affects the determination of depth of foundation. Calculation for foundation depth is done based on type of soil, ground water table, loads from structure, bearing capacity of soil and other factors. General factors to be considered for determining depth of foundation are: 1. Load applied from structure to the foundation 2. Bearing capacity of soil 3. Depth of water level below the ground surface 4. Types of soil and depth of layers in case of layered soil 5. Depth of adjacent foundation The minimum depth of foundation should be considered to ensure that the soil is having the required safe bearing capacity as assumed in the design. However, it is advised to carry out soil investigation before deciding on depth of foundation. Soil investigation report will suggest the foundation depth based on the type of structure, soil properties, depth of water table, and all other variable that should be considered. Soil investigation report provides bearing capacity of
Read more

WHAT IS VOLUME BATCHING OF CONCRETE AND HOW IT IS DONE IN FIELD?

Image
WHAT IS VOLUME BATCHING OF CONCRETE? Batching of concrete means measuring different ingredients of concrete (i.e. cement, sand, coarse aggregate and water) before mixing it. When this measurement is done on the basis of volume, we call it  Volume Batching . Below are mentioned some of important points to remember before adopting volume batching method in field. Volume batching is not a good method for measuring concrete materials. It is not applicable in case of reinforced concrete structure. This method of concrete batching may not be economical. It can be only used for unimportant concrete or for small concrete works. HOW VOLUME BATCHING IS DONE IN FIELD? Before batching concrete ingredients in terms of volume, we need to know two things. What is the relative proportion of concrete ingredients in terms of volume? What is the water-cement ratio? After knowing these two things you can proceed to batch concrete ingredients in field. The table shown below can be
Read more

Construction Project Management Softwares

Image
Construction PM Software A new wave of web and cloud apps are streamlining communication, simplifying document management, and improving efficiency in construction management.  Here are some of top construction management tools: Smartsheet Smartsheet  is a spreadsheet-inspired work management tool with robust collaboration and communication features. With pre-built construction templates, it’s easy to create a timeline, track progress, manage documents, and organize the details. Gantt charts are automatically created and auto-adjust every time a change is made, so you can share the most up-to-date timeline with team members or stakeholders. You can upload files from your computer, Google Drive, Box, Dropbox, Evernote, or add a web URL, creating a central repository for all project documentation and contracts. Team members can have discussions directly in the sheet and set reminders and alerts, so everyone is on the same page. And lastly, Smartsheet integrates with ot
Read more

Methods of underpinning, Procedure and Applications in Foundation Strengthening

Image
Underpinning is a method for repair and strengthening of building foundations. Underpinning methods, procedures and their applications in strengthening of different types of foundations is discussed in this article. There are situations where a failure in foundation or footing happens unexpectedly after the completion of whole structure (both sub and superstructure). Under such emergency situation, a remedial method has to be suggested to regain the structural stability. The  method of underpinning  help to strengthen the foundation of an existing building or any other infrastructure. These involve installation of permanent or temporary support to an already held foundation so that additional depth and bearing capacity is achieved. Selection of Underpinning Methods Underpinning methods are selected based on age of structure and types of works involved. Structure categories based on its age: Ancient Structures :Age greater than 150 years Recent Structures : Age between 5
Read more

Methods for Calculating Cost of Engineering Consultant Services

Image
here are several methods by which calculation of engineering consultant services cost can be carried out in construction. It is possible to employ various charging approach at different phase of the consultant services. The application of each method or combination of methods is dependent on nature, scope and complexity of the required engineering services. In this article, these charging consulting services are discussed. Following are the topics discussed for calculating cost of engineering services or consulting services in construction: What are the factors that affect the engineering service cost? Methods for charging engineering services What are the Factors that affect the Engineering Service Cost in Construction? There are various factors that control the cost of engineering services required for a specific project. These factors are outlined below: The conditions at project site. Degree of danger that may be encountered and exposure possibility. System of pr
Read more